menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"
    config BSP_USING_STLINK_TO_USART
        bool "Enable STLINK TO USART (uart2)"
        select BSP_USING_UART
        select BSP_USING_UART2
        default y

    config BSP_USING_ARDUINO
        bool "Compatible with Arduino Ecosystem (RTduino)"
        select PKG_USING_RTDUINO
        select BSP_USING_STLINK_TO_USART
        select BSP_USING_GPIO
        select BSP_USING_ADC
        select BSP_USING_ADC1
        select BSP_USING_PWM
        select BSP_USING_PWM1
        select BSP_USING_PWM1_CH3
        select BSP_USING_PWM1_CH2
        select BSP_USING_PWM1_CH1
        select BSP_USING_I2C
        select BSP_USING_I2C1
        select RTDUINO_USING_WIRE
        imply RTDUINO_USING_SERVO
        default n
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default n

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default y

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM

        if BSP_USING_PWM
            menuconfig BSP_USING_PWM1
                bool "Enable timer1 output PWM"
                default n
                if BSP_USING_PWM1
                    config BSP_USING_PWM1_CH1
                        bool "Enable PWM1 channel1"
                        default n
                    config BSP_USING_PWM1_CH2
                        bool "Enable PWM1 channel2"
                        default n
                    config BSP_USING_PWM1_CH3
                        bool "Enable PWM1 channel3"
                        default n
                endif
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            comment "Notice: PB8 --> 24; PB9 --> 25"
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 80
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 80
                default 25
        endif

    source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu