menu "Hardware Drivers Config" menu "Onboard Peripheral Drivers" config BSP_USING_STLINK_TO_USART bool "Enable STLINK TO USART (uart2)" select BSP_USING_UART select BSP_USING_UART2 default y config BSP_USING_ARDUINO bool "Compatible with Arduino Ecosystem (RTduino)" select PKG_USING_RTDUINO select BSP_USING_STLINK_TO_USART select BSP_USING_GPIO select BSP_USING_TIM select BSP_USING_TIM9 select BSP_USING_ADC select BSP_USING_ADC1 select BSP_USING_PWM select BSP_USING_PWM1 select BSP_USING_PWM4 select BSP_USING_PWM3 select BSP_USING_PWM2 select BSP_USING_PWM2_CH2 select BSP_USING_PWM3_CH1 select BSP_USING_PWM2_CH3 select BSP_USING_PWM3_CH2 select BSP_USING_PWM4_CH1 select BSP_USING_PWM1_CH1 select BSP_USING_I2C select BSP_USING_I2C1 select BSP_USING_SPI select BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA select BSP_SPI1_RX_USING_DMA select RTDUINO_USING_WIRE select RTDUINO_USING_SPI imply RTDUINO_USING_SERVO default n endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART2 bool "Enable UART2" default y config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_USING_UART6 bool "Enable UART6" default y config BSP_UART6_RX_USING_DMA bool "Enable UART6 RX DMA" depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA default n endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 comment "Notice: PB8 --> 24; PB9 --> 25" config BSP_I2C1_SCL_PIN int "i2c1 scl pin number" range 0 80 default 24 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 0 80 default 25 endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM1 bool "Enable timer1 output PWM" default n if BSP_USING_PWM1 config BSP_USING_PWM1_CH1 bool "Enable PWM1 channel1" default n endif menuconfig BSP_USING_PWM2 bool "Enable timer2 output PWM" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH2 bool "Enable PWM2 channel2" default n config BSP_USING_PWM2_CH3 bool "Enable PWM2 channel3" default n endif menuconfig BSP_USING_PWM3 bool "Enable timer3 output PWM" default n if BSP_USING_PWM3 config BSP_USING_PWM3_CH1 bool "Enable PWM3 channel1" default n config BSP_USING_PWM3_CH2 bool "Enable PWM3 channel2" default n config BSP_USING_PWM3_CH4 bool "Enable PWM3 channel4" default n endif menuconfig BSP_USING_PWM4 bool "Enable timer4 output PWM" default n if BSP_USING_PWM4 config BSP_USING_PWM4_CH1 bool "Enable PWM4 channel1" default n endif endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM9 bool "Enable TIM9" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n menuconfig BSP_USING_SPI bool "Enable SPI Bus" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 Bus" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI3 bool "Enable SPI3 Bus" default n config BSP_SPI3_TX_USING_DMA bool "Enable SPI3 TX DMA" depends on BSP_USING_SPI3 default n config BSP_SPI3_RX_USING_DMA bool "Enable SPI3 RX DMA" depends on BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA default n endif source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu