menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_ARDUINO
        bool "Compatible with Arduino Ecosystem (RTduino)"
        select PKG_USING_RTDUINO
        select BSP_USING_STLINK_TO_USART
        select BSP_USING_UART2
        select BSP_USING_UART3
        select BSP_USING_GPIO
        select BSP_USING_ADC
        select BSP_USING_ADC1
        select BSP_USING_PWM
        select BSP_USING_PWM2
        select BSP_USING_PWM2_CH1
        select BSP_USING_PWM2_CH2
        select BSP_USING_PWM3
        select BSP_USING_PWM3_CH1
        select BSP_USING_PWM3_CH2
        select BSP_USING_PWM3_CH3
        select BSP_USING_PWM3_CH4
        select BSP_USING_I2C
        select BSP_USING_I2C1
        select BSP_USING_SPI
        select BSP_USING_SPI2
        # select BSP_SPI2_TX_USING_DMA
        # select BSP_SPI2_RX_USING_DMA
        select RTDUINO_USING_WIRE
        select RTDUINO_USING_SPI
        imply RTDUINO_USING_SERVO
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number (PB8)"
                range 0 143
                default 24
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number (PB9)"
                range 0 143
                default 25
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM2
            bool "Enable timer2 output PWM"
            default n
            if BSP_USING_PWM2
                config BSP_USING_PWM2_CH1
                    bool "Enable PWM2 channel1"
                    default n

                config BSP_USING_PWM2_CH2
                    bool "Enable PWM2 channel2"
                    default n
            endif

        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output PWM"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH1
                    bool "Enable PWM3 channel1"
                    default n

                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n

                config BSP_USING_PWM3_CH3
                    bool "Enable PWM3 channel3"
                    default n

                config BSP_USING_PWM3_CH4
                    bool "Enable PWM3 channel4"
                    default n
            endif
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n

            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n

            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

     menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n

        endif

    config BSP_USING_USBD
        bool "Enable USB device"
        select RT_USING_USB_DEVICE
        default n

    source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu